$1650.0 Buy It Now or Best Offer
free,30-Day Returns
Seller Store skipwhite
(211374) 99.8%,
Location: Kingsport, Tennessee
Ships to: US,
Item: 373995832080
Restocking Fee:20%
Return shipping will be paid by:Buyer
Returns Accepted:Returns Accepted
Item must be returned within:30 Days
Refund will be given as:Money Back
Manufacturer Part Number:Does Not Apply
SCAT EAGLE WISECO:SCAT EAGLE WISECO
Manufacturer Warranty:Yes
FULLY BALANCED BBC CHEVY 496 ROTATING ASSEMBLY WITH WISECO FORGED +30cc DOME PISTONS. 4.310 BORE X 4.250 STROKE, .060 OVER. SCAT OR EAGLE BALANCED CRANKSHAFT. SCAT 6.385 COMPETITION RODS. FITS 2PC REAR MAIN SEAL BLOCKSImportant note.Our eBay user id is: skipwhite, and our eBay store name is whiteperformance1. You may have noticed other sellers using a similar name offering similar products. These other sellers have capitalized on our name as we see it, and many customers searching for us will inadvertently find them, thinking we are one in the same company. There is only one “Skip White.” We are the original premier eBay seller under this name since approximately 2003. We have no other eBay names, nor are we associated with any other company regardless of the similarity in the name or location. Our official company name is Skip White Performance. Please see the article in the lower part of this ad for a more detailed explanation The picture above is a file photo. See the detailed info below for the actual pictures and items included in this assembly. Fully balanced in house. READ THIS LISTING COMPLETELY BEFORE YOU BUY ELSEWHERE! This assembly comes with a Scat or Eagle crankshaft and 4340 Scat rods, Mahle moly rings, King bearings, and a heavy duty 168 or 153 tooth flexplate and a Pro-Race brand Pro-Sport Series SFI damper. See details for all the actual specs of this assembly. In the lower section of this ad is information on the various upgrades we offer in our other listings. ********************************************************** We offer these assemblies in 1 pc rms. and 2 pc rms. dish, dome or flat top pistons, as well as other bore sizes. See details below for the actual specs.Crankshaft Specs. Crankshaft: Genuine Scat or Eagle, depending on availabilityCrankshaft Stroke: 4.250″ Crankshaft Material: Cast Nodular Steel. Forged 4340 crank available as an upgrade. Journal Diameter: STD BBC Rear Main Seal: 2pc RMSConnecting Rod Specs.Rods: Genuine Scat Rod Type: Scat Pro-Competition, I-beam, Bronze Bushed.Rod Length: 6.385″Rod Material: Forged 4340 Alloy.Rod Bolt/Cap Screw: ARP 8740 Cap Screws.Piston & Ring Specs. Pistons: Wiseco Fully Forged. High Performance for street/strip use.Piston Size: 4.310″Dome Volume: +30cc Dome TopCompression Height: 1.280Piston Material: Forged 2618 Aircraft AlloyPiston Rings: Mahle Moly, Standard Tension.Ring Size and Fit: 5/64 5/64 3/16 Drop In.Ring Material: Ductile Iron/Cast/Stainless/MolyBearing, Damper, and Flexplate Specs.Main Bearings: King MB557SIRod Bearings: King CR807SIBalance: In House on CWT balancer.Damper: Pro-Race brand Pro-Sport Series SFI 7.0″ Flexplate: Heavy Duty 168 tooth or 153 tooth. Manual Trans. flywheels available. Compression Ratio ChartThe calculations below assume your pistons are at zero deck. Let’s say your compression calculates out to be 10.50:1 for example based on having the pistons at zero deck (flush with the deck), but your pistons were going to be .005 in the hole, then the comp. ratio would only drop to approx. 10.36, and if left .010 in the hole, then it would drop to approx. 10.22 We do recommend having your block decked to allow the piston to set anywhere from flush (zero) to .005 in the hole for optimal performance. We used a 4.560 head gasket diameter, and a .040 head gasket thickness in our calculations to come up with our comp. ratio values. Part NumberCylinder Head Volume106cc117cc119cc121ccBBC STROKERStatic Compression Ratio4.310 Bore12.7211.4011.1910.99 Listed below is a complete breakdown of all the parts that are included in this assembly. WISECO FULLY FORGED PISTONS, RATED AT 800+ HP. WISECO PISTONS ARE 100% MANUFACTURED IN THE USA. THEY ARE ONE OF THE HIGHEST RATED PISTON BUILDERS IN THE COUNTRY.Our custom made Wiseco pistons are rated very high in the street/strip performance industry. Wiseco normally offer several grades of pistons, starting with the lower grade Pro-Tru Street version made with 4032 forged alloy. The next level up would be the professional series that are much more expensive and made from 2618 aircraft alloy and have fully machined crowns rather than the as cast crowns that are on the Pro-Tru series. Our Wiseco pistons are custom made for us, and have both of these premium features, 2618 Alloy, and fully machined crowns. All premium grade forged pistons on the market have these two unique features and usually cost around $800-$1100 per set. We prefer the 2618 alloy over the lower cost 4032 alloy. The 4032 alloy may fragment from the effects of detonation and if this happens, it can be very destructive to the engine. Those types of pistons are fine for stock or mild engine builds, but should never be used in carbureted engines built to high horse power levels. The forged 2618 alloy piston is much more resistant to the effects of detonation and heat. We have built approximately 8000 engines using the Wiseco pistons over the past 10 years. The engines have been for street rod and strip use. We have seen no problems, nor have there been any complaints. They are an excellent product in every respect.Important noteMany customers have asked us what size they should bore their block at to allow for a proper piston to wall clearance. The required clearance is built into the piston already. For example if these pistons show a given size such as 4.030 then that is exactly what you will bore the block to. The actual size of the pistons when measured at the skirt, 1/2 inch above the tang will show to be approx. 4.026. The needed clearance is built in. Should you be using these pistons in a marine app. where the boat receives it’s water from the lake, then an additional 1.5-2.0 thous. would be added to your final bore size, and some forced induction apps may also require a slight increase in bore size. These pistons are totally suitable for use with mid level nitrous or blower setups. Extreme level builds that are making hp numbers in the 1000 hp range will require a set of custom made extreme duty pistons.Our Wiseco Forged pistons are custom designed with an increase in compression height. This has many advantages. Here are a few facts about compression height and deck height.Our custom made Wiseco pistons have a compression height that is .010 taller than nearly all catalog pistons on the market. We find this to be a very valuable feature. Since our pistons sit at a taller than normal compression height, you will only have to remove approx. .005-.010 off the deck surface of a virgin block to achieve a zero deck. This also allows for future deck re-surfacing and still not ending too far below stock deck height. Leaving the deck on your block thick makes for a stronger block that resists flexing and also runs cooler, as the deck thickness has a lot to do with the dissipation of heat. Blocks with decks cut down to any great amount are also prone to cracking. This is why our pistons are designed to sit flush, (zero deck) at .010 below stock deck height.Since nearly all bbc catalog pistons on the market sit .020 below the surface of a virgin block, the only way to achieve a zero deck using such pistons would be to cut .020 off the deck surface. This compromises the integrity of the block, in our opinion. Should you decide to leave the block deck higher up, using such pistons creates a new issue of having a very poor quench/squish zone. The only way you could really take advantage of a catalog piston is by having a block that needs to or has already been butchered down to 9.780 deck height. Having the piston sitting flush with the deck is very desirable, regardless of the fact that your overall compression ratio is slightly higher than if it were sitting below the deck. We have found that 95% of our customers are using a virgin block or a block that is close to stock deck height. This is why we have designed our pistons to have a taller compression height. On very rare occasions, you may end up with a block that has the piston out of the hole by a few thousandths and this not a problem at all. Most head gaskets are approx. .040 thick, and should you end up with a quench zone of .035, then that is ok. If the quench zone ends up below .035, then there are plenty of .050 thick head gaskets on the market. One more benefit to this is that most machine shops charge much more to deck a block down from stock deck height to 9.780 than they would to do a light cleanup, and that’s all that’s needed when using our Wiseco pistons. Another good feature about our pistons having a taller compression height is that the ring land above the top ring is much stronger by being .010 thicker. When pistons encounter the effects of detonation, it is not uncommon to see pistons with the ring land above the top ring broken off. The thicker ring land also makes a better heat sink. You may have noticed that our Wiseco custom made forged pistons are referred to as Racing Pistons on the package. This does not mean that the pistons are for racing only. This is a generic term, referring to their ability to be used in high performance applications as well as for street rod use. These pistons are perfectly designed for use on the street, as well as for medium to upper level drag racing. Our custom made Wiseco forged pistons are made from 2618 aircraft alloy. We find this alloy to be much more suitable for high performance engines than the common 4032 forged alloy. You will usually see the higher end pistons on the market using 2618 aircraft alloy. Why go with 2618 forged pistons? If you encounter certain tuning issues, detonation is highly probable, and it’s effects can cause severe damage to your engine. The 2618 forged piston is able to withstand the damaging effects from detonation to a higher degree than the lower cost 4032 forged pistons, especially non-forged hypereutectic pistons such as Speed Pro or Keith Black, and many others. Our Wiseco forged pistons will clear most any valve size on the market with ease even with the use of large lift cams. The pictures below are file photos of our Wiseco pistons. Scat or Eagle Crankshaft.The picture below is a generic file photo. You will receive the correct crankshaft. This assembly comes with a cast nodular steel crankshaft. We offer the 4340 forged crankshaft as an upgrade. See the upgrade list in the lower portion of this ad.We recommend that you check the thrust clearance on the crank before assembling the engine. This is recommended on any crankshaft, regardless of brand or cost. Also be sure to check your main and rod journal size.Our choice of rods are the SCAT COMPETITION SERIES rods with ARP-8740 cap screws. The Scat Pro-Comp extreme duty I-beam rods should not be mistaken for ProComp rods. These rods are made exclusively by Scat, and have nothing to do with the ProComp company. The critical sizing and installation of the ARP cap screws is performed on a Sunnen machine in the USA by Scat Industries. These rods are excellent for those wanting the extra security offered by a rod with 7/16 ARP cap screws. Take notice of the design of these rods. They are far superior to conventional style I-beam rods. We are now using this rod in all of our Stage 4 and up SBC engines. We also use this rod in our big block 540/555 engines, making approx. 700+hp If you do a search on the Scat Pro-Comp rods, you will find a vast amount of info on many car forums. All of the info is 100% positive. These rods are run in engines that not only produce high horsepower levels, but also run at continuous RPM. Notice the general appearance in the pictures. These rods do look impressive. The style is reminiscent of a steel billet rod.The fact that these rods are incredibly strong and well made, coupled with the fact they are light weight and offer better clearance than any H-Beam rod on the market, made it an easy decision to use them in all of our high horsepower street/strip engines. The Scat rods do have genuine ARP 8740 Series 12 point cap screws. These rods offer excellent block clearance in the lower end of the cylinders. We have noticed some sellers using generic rods and crankshafts in their rotating assemblies. These non-branded (no-name) rods and cranks are often poor quality in many ways. You will notice many sellers fail to mention the actual brand of these products. Upon further investigation, you will find such parts not to be a branded name product. They may label these parts with a name, but one that is totally unrecognizable in the industry. Our experience in years past with such rods and cranks has been disappointing, to say the least. Failures of such critical parts in your engine may result in catastrophic damage. Machine shops are sometimes able to correct some of the problems with these low quality rods and cranks, but at great expense to the customer. As for the questionable alloy these items may be produced from and the potentially incorrect heat treating methods used, little can be done to verify this and nothing can be done to correct it. As you may have noticed, this is why we specify the name brand and series of every part used in our assemblies.Genuine ARP 8740 cap screws. Many of the inferior “no-name” rods on the market will also have “no-name” rod bolts in them. We have seen these bolts before, and they are very low quality. They don’t have ARP’s rolled thread design, and they don’t torque down with the same characteristics as a genuine ARP bolt. It’s not just a matter of having a different brand bolt in the rods; these bolts are low quality in many ways. They have been known to fail in engines to a much greater degree than a high quality rod bolt, and this failure usually causes catastrophic damage in the engine. Beware of rods that don’t mention the rod bolt brand. As far as we’re concerned, ARP bolts are the only brand we would ever use or accept in a set of rods.Before the engine is assembled, we strongly suggest checking the rods on a Sunnen machine for sizing on both ends. We recommend this with any rod regardless of cost or brand. It is not uncommon to find some of the rods requiring a slight bump through the hone for perfection in sizing and roundness. We also offer this kit with a proofed set of rods. This is an excellent choice for those wanting to build the engine on their own. MAHLE MOLY RING SET INCLUDED. THIS IS UNDOUBTEDLY THE BEST RING SET MADE FOR THESE PISTONS. DROP-IN, NO FILING REQUIRED. Mahle ring sets feature standard ring end gaps (drop-in) for easy installation. KING BEARINGS. Pro-Sport harmonic SFI damper, 7.0 diameter, included. The SFI Pro-Sport damper Offers an extreme level of safety against breakage, and is very resistant against slippage of the elastomer damping material. SFI dampers are not only made from a better grade of steel, they are also constructed differently and have a much better appearance. They usually last much longer than a non-SFI damper. Many drag strips require this on engines producing high horse power levels. The SFI certification is laser etched into the side. Damper failure rates are much higher on engines using a non-sfi damper coupled with hp ratings exceeding 450 and turn 5600 rpm or higher.We have noticed others using a low grade knockoff brand damper/balancer, and we have encountered them in the past. They are substandard in appearance, and are often out of spec. The timing marks were also poorly marked on some of the balancers we have come across. You don’t want a balancer coming off or one that is improperly weighted. Another problem with low grade dampers is the elastomer bonding can lose its adherence to the inner and outer structure. This problem is referred to as a slipped damper. We have only encountered this once in 10 years with the Pro-Race brand dampers. Damper failure rates are much higher on engines using a non-sfi damper coupled with hp ratings exceeding 450 and turn 5600 rpm or higher. We strongly recommend our upgrade SFI damper. See our upgrade list below.We know of several competitors including these balancers with rotating assemblies. The Pro-Sport SFI is far superior to most any we have ever seen. They were once known as a knockoff product, and have become one the best values on the market, without comprising quality whatsoever. HEAVY DUTY FLEXPLATE INCLUDED. HEAVY DUTY FLEXPLATE. This flexplate will resist cracking. One good telltale in identifying a low quality flexplate is the lack of welding on each side where the plate mates to the ring gear. They usually have a pale grey color to them, as they are not coated, and will rust quickly. Ours are welded on both sides, and are much thicker than an OE plate, and are either zinc dichromate or black powder coated. We would never use the thinner OE style plate on an assembly like this. WARNING: The crank has a dowel pin installed in it. You must align the flexplate or flywheel to the dowel pin. The assembly was balanced with this pin installed. We offer premium grade Ram brand SFI Billet Steel flywheels for manual transmission use at an additional cost. See our other listings. This assembly includes a flexplate for automatic transmission use at no additional cost. When choosing a flywheel for manual transmission use, be sure to know what tooth count you need. There are two sizes available, and it is of the utmost importance to select the flywheel that is correct for this assembly. There are several factors that must be addressed when choosing your correct flywheel. The tooth count must be correct. This is very important. There are two sizes available, and it is the bellhousing size on the transmission that determines this. Another important factor is if the assembly your purchasing is internally balanced often referred to as neutral balanced or if it is an externally balanced assembly, often referred to as externally balanced. All of our assembly ads will have this information in them. Big block and small block engines will also have a different bolt pattern in most cases. To sum it up, there are three important factors to look for when selecting the correct flywheel, tooth count, int. or ext bal. and whether or not you have a big block or small block engine. The Ram brand flywheels we offer are very high quality. Our CWT 5500 Balancer.We do our own balancing with our new state of the art CWT 5500 Series balancers. The CWT 5500 is the ultimate for precision balancing. We now have three of these in our machine shop. We consider this machine to be highly advanced compared to the Hines balancer we once used. We balance every rotating assembly we sell within 2 grams or less at no extra charge. A balance sheet is included with your assembly. Three CWT balance machines under one roof is a rare sight. Our crew wrapping up for the day. Pardon the mess.Rust warning.If you are going to store your rotating assembly or short block kit for any length of time, it is very important that you protect these parts by spraying a light coat of rust preventive substance on all bare metal parts. This is especially important for those storing these parts in a high moisture or humid environment. Very light surface rust is easily removable and will cause no harm, but heavy rust can damage these parts and be very costly to fix.Our thoughts on what the competition has to offer.Many rotating assemblies we see on the market are not using the most suitable parts. We hope you can value the fact that we have put together an above average assembly. The failure rate with the parts used in our assembly is near non-existent. These are the same parts we use in our engine program. It was through trial and error in years past that taught us where to draw the line with low cost parts. We are out-priced by many others selling assemblies that include parts that have high failure rates. Many of these parts also pose a great problem with assembly due to the fact they require additional machining and can end up costing you a great deal more money and time. If you’re going to have a machine shop build your engine, we strongly advise you get an opinion from them on the parts you’re going to be bringing to them. Rest assured they will find no problem with the combination and quality of our parts. We have also seen sellers offering parts that are not compatible with what most people are building. The low grade dampers and flexplates are often a problem. Another area of concern would be balancing. Not sure how much attention these sellers are giving the assembly in this area. We spend up to two hours balancing an assembly, and using the very best up to date CWT balancing equipment on the market. If the assembly is not balanced properly, it will cost you horse power, and it can damage the bearings in the engine, not to mention there is nothing worse than an engine that lacks a smooth feel and sound when ran in the upper rpm range.We offer this assembly with selected upgrades. Listed below are some of the most requested ones. Many not only improve performance, but further enhance the reliability and longevity of your engine, along with resale value.Note: The upgrade prices below are subject to change. Refer to the actual ugrade listing for the exact price of these upgrades. The changes are usually very small if any.SFI Certified Flexplate: This is a very low cost upgrade and may be required when racing your car at certain tracks. The flexplate that comes with this assembly is a heavy duty plate, but the SFI certified plate is one step up in quality and safety. This SFI plate is made in North America. We noticed these have much less run-out and warpage than we see with many other plates on the market. Plates with too much run-out and warpage can cause a host of problems for your transmission and starter, and affect balancing. The low cost to upgrade to this is well worth, it in our opinion.Cost of this upgrade is $24.50 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the “UPGRADES” category, or simply do a search with the key word, “Upgrade” in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. On occasion we are unable to obtain the Pioneer brand SFI flexplate and will substitute it for the Scat SFI brand plate pictured below. The quality is equal in every aspect. Crank polishing: Extends bearing life, reduces oil temp, frees up a slight amount of average horsepower. This is a very low cost upgrade, and in the world of mass production, most cranks do not come with a true polished finish. This is why most machine shops have a machine to do this. The difference is dramatic between a crank right out of the box and one that we have polished. Bearing companies claim that cranks that have better finishes on the journals will survive the break-in better, and have much longer bearing life. We do a two-step process and bring the RA numbers down in the single digit range. We have the most advanced crank polishing machine on the market. Cost for the crank polishing upgrade is $39.50 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the “UPGRADES” category, or simply do a search with the key word, “Upgrade” in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Clevite Bearings: We find the Clevite bearings to be a somewhat better product overall. Clevite is what we now use in all of our engines. This is not to say that King bearings are faulty in any way, but under certain conditions, we have seen fewer problems develop with Clevite bearings during break-in. We have sold King bearings for many years and do not hear of problems from our customers, but our experience on the dyno has shown the Clevite bearings have a better surface appearance upon tear-down after many dyno passes.Upgrade to Clevite “A” Series (for cast crank only) bearings is $45.00Upgrade to Clevite “H/HN” Series (with forged crank upgrade) bearings is $60.00We have these Clevite bearing upgrades featured in our other listings. You can see these and other upgrade options in our ebay store under the “UPGRADES” category, or simply do a search with the key word, “Upgrade” in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Rod sizing: Sizing the big end and wrist pin bushing on the Sunnen machine saves a trip to the machine shop. All rods, regardless of brand, should be checked for sizing on a Sunnen machine, and corrected if needed. You will seldom see a complete set of rods that have perfect sizing on both ends right out of the box.Cost of this rod sizing upgrade is $50.00 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the “UPGRADES” category, or simply do a search with the key word, “Upgrade” in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Race balancing: This is for those who want the engine to operate virtually vibration free at high rpm. Extends engine life and frees up a few more horse power. This is a somewhat labor intensive procedure and is not required, but the feel of an absolutely vibration free engine at high rpm is desirable by many. The standard balance job that is included with this assembly at no extra charge is certainly sufficient. With a race balance job, all pistons and rods are match weighed to within 2/10’s of a gram or less, and the final balance is brought down to around 1 gram plus or minus. An ultra smooth engine at high rpm has a noticeable feel and sound to it. If you do not opt for this upgrade, the assembly will still be fully balanced. We spend a good hour and a half doing the regular balance work, and it will certainly meet your needs. Cost of this race balancing upgrade is $125.00 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the “UPGRADES” category, or simply do a search with the key word, “Upgrade” in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Scat H-Beam Rods: Recommended for those running hard. The Scat Competition rods that come with this assembly are sufficient for most street rod uses, but the Scat H-beam rods will most likely offer more security against rod breakage under hard use. The H-beam rods have a 750+ HP rating.Cost of this Scat H-beam rod upgrade is $89.50 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the “UPGRADES” category, or simply do a search with the key word, “Upgrade” in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. ARP-2000 rod bolts: This is one upgrade that we find to be very valuable. The rod bolts are most likely to fail under hard use, more so than the rod itself. When a rod bolt fails during high RPM, total engine destruction is usually the result. The ARP-2000 rod bolts are a very good upgrade, in our opinion. We actually have few, if any, problems with the regular ARP-8740 bolts, but those who run hard always upgrade to the ARP-2000 rod bolts. The ARP-2000 rod bolts also torque at a higher number, and this increased clamping force is also a factor in keeping the big end of the rod stable and true to size. The ARP-2000 bolts are installed in the rods and this upgrade is only available with the Competition rod upgrade. Cost of this ARP 2000 rod bolt upgrade is $89.50 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the “UPGRADES” category, or simply do a search with the key word, “Upgrade” in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Scat or Eagle 4340 Forged Crank: The forged crank has a rating of 800+ HP. This is the ultimate upgrade for those wanting to run hard. Nos, blowers, turbos, are not an issue with this crank. Even without such power adders, this Crank offers great protection under the most severe conditions. This upgrade also comes with the high Performance King bearings. Should you decide to run power adders in the future, this would be essential. The fatigue life of the 4340 crank over the cast nodular is also greatly extended. We do offer this upgrade as part of many of our assemblies in our other listings. They have the key words, “fully forged,” in the title.Cost of this forged crank upgrade is $585.00 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the “UPGRADES” category, or simply do a search with the key word, “Upgrade” in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. The upgrades above are all available in our other listings. Some of these are often requested by those building an engine without a machine shop. We find most of these upgrades very valuable for those wanting to take longevity and durability to the next level. They are all bottom end related, and that’s an area worth investing a few more dollars into, in our opinion, especially if you’re planning on running long and/or hard. These upgrades are also valuable for your build history on your engine, and would certainly increase the resale value of your engine, should you ever sell it. A note from Skip White, company president.Many people have asked how is it that we can sell this assembly for such a low price. To answer this; we buy our products at master WD (warehouse distributor) level for all of the items in this assembly, and we are selling direct to the public. We are a volume sales based company. Our profit is based on sheer volume, with a very low markup. It is this large volume purchasing that allows us to buy products at a much lower price and we simply pass these savings on to our customers. This is our main competitive edge.Skip White A final note.Our eBay user id is: skipwhite, and our eBay store name is whiteperformance1. You may have noticed other sellers using a similar name offering similar products. These other sellers have capitalized on our name as we see it, and many customers searching for us will inadvertently find them, thinking we are one in the same company. There is only one “Skip White.” We are the original premier eBay seller under this name since approximately 2003. We have no other eBay names, nor are we associated with any other company regardless of the similarity in the name or location. Our official company name is Skip White Performance. Please see the article below for a more detailed explanation.The real story…Skip White Performance vs. White Performance & MachineI’m sure many of you have noticed there are two high performance engine builders in Kingsport, TN with similar names, and this has led to a great amount of confusion.We are Skip White Performance, NOT White Performance and Machine or Marine or any other similar name. Many customers looking for us online inadvertently find them, thinking we are the same company. Definitely not…there is no connection between the two companies. We don’t have a problem with free enterprise (competition). However, when the competition builds their foundation on such things as a name similarity and their supposedly long history of being in business, then we think it’s about time we set the record straight.We have owned White Performance since 2003, with the exception of the machine shop, which was owned by Fred White at the time. He continued to operate the machine shop and build engines for us while we continued selling online under the eBay user ID of skipwhite and the eBay store name of whiteperformance1.Due to their limited production capability and many disagreements about the engine building process and workmanship, we opted to open a full scale machine shop of our own. Fred White began competing against us even though our contract had a no compete clause in it. Fred White sold his machine shop in 2016. As our business grew over the years, we expanded our operation, and have become the number one street rod engine building in the nation. Due to the name similarity, many people looking for us mistakenly contacted Fred’s shop. The problem continues to this day and the new owners of Fred’s shop reap the benefits from this confusion between the two shops. Fortunately we stay plenty busy throughout the year, but a new problem has come up. We’re getting calls nearly on a daily basis from people that realize there are two shops in this town with very similar names and complain of serious problems in getting their engine in a timely manner from them. They think they purchased their engine or rotating assembly from us. Due to the confusion, there was an increasing amount of negative talk that is starting to reflect on our reputation within the street rod community, when in fact we have a near perfect reputation in this industry.All in all, we have been in this business for going on 21 years. By putting heart and soul in this company, we have become the number one street rod engine builder in the country. Skip White’s passion has been owning and building street rods for 51 years on a personal level. The knowledge he has gained over time has allowed him to venture into this business and succeed to a very high level.As mentioned above Fred White sold his machine shop to an investor in early 2016. This investor lacks any knowledge of this industry. They continue to use the White Performance & Machine name. Fred White is no longer associated with the company in any way. Their main spiel in advertising is, “In business since 1979,” when in fact, we purchased the White Performance company in 2003, with the exception of the machine shop. The great pretenders continued capitalizing from our success, but as mentioned, have been degrading our reputation. (Update, The people that took over Fred Whites machine shop are no longer in business as of the past couple years.) FAST FORWARD TO 2023…We have become the largest street rod engine builder and supplier of rotating assemblies in the nation. Our engines, rotating assemblies, and cylinder heads are built to very high standards and shipped to our customers in a timely manner. We are a premier seller on eBay with a positive feedback score of well over 212,000.Our engines are custom-built to our customers’ specifications and are shipped, in general, in 2-5 weeks, perhaps sooner, depending on the season. Our rotating assemblies ship out in about one week, and our heads ship in about a week or less.Now you know the real story, and we hope this helps with the confusion.RETURN POLICY Should a problem occur, please contact us. If a return is necessary, please contact us for an RGA number and return authorization. The RGA number must be included on the return label. If an item is returned without an RGA number, it will not be processed. A full description of what the problem is needs to be included with any returned product with your contact info, and proof of purchase. Even though you may have explained the problem to us, and been granted permission to return the product, we must have a written explanation and a contact number included with the product. It is also recommended that you include the name of the person from our company that you have been in contact with. You must send the item back to us in a trackable manner (USPS Priority Mail, FedEx, etc.) and keep the tracking info of the returned product. Please give ample time for returns to be processed. Following these guidelines will make the return process work as it should. PAYMENT AND SHIPPING DETAILS. We offer great discounts on shipping. You only pay the full shipping fee on the highest shipping cost of your items, and HALF PRICE shipping on all additional items. Few offer discounts on shipping such as this. Our checkout system will automatically calculate your shipping discount at the time of final payment, providing you consolidate your payment. You may receive a verification and tracking number shortly after purchase, but this does not necessarily mean that your product has shipped. It would be fair to say that 98% of products will be going out the day the shipping label is issued. On occasion, the product may not ship out until the next day after the label has been issued. Most products purchased late in the day will not be shipped until the next day. If you checkout and start over, the auto calculator will not recognize the multiple purchases, and there will be no shipping discount. UPS is our primary shipper. We are unable to ship to APO/FPO addresses or PO Boxes. Help us ship your order promptly by including your physical address at checkout. Below is a map representing the estimated delivery time to get to you from our location. Delivery times may vary, especially during peak periods. UPS delivers Monday – Friday, except for national holidays. If a package leaves here on a Thursday, and you are in a 2 day delivery zone, your package will deliver to you on Monday. Expedited shipping is available upon request for an additional fee. Please contact us for rates. The estimated shipping time is usually as the map shows, but many factors can delay this. Alaska is in a 3-day ship zone, Hawaii is in a 6-day ship zone, and Puerto Rico is in a 4-day ship zone. Additional fees will apply to shipments to these areas, as noted below.The shipping quoted in this ad is only for the 48 continental United States. If shipping to anywhere else, please contact us. The half price shipping on all additional items also only applies to items that are being shipped in the 48 continental United States.
Frequently Asked Questions About BBC CHEVY 496 ASSEMBLY SCAT & WISECO +30cc DOME 4.310 PISTONS 060 OVER 2PC RMS in My Website
biesalab.org is the best online shopping platform where you can buy BBC CHEVY 496 ASSEMBLY SCAT & WISECO +30cc DOME 4.310 PISTONS 060 OVER 2PC RMS from renowned brand(s). biesalab.org delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.
What are the best-selling BBC CHEVY 496 ASSEMBLY SCAT & WISECO +30cc DOME 4.310 PISTONS 060 OVER 2PC RMS on biesalab.org?
biesalab.org helps you to shop online and delivers We11done to your doorstep. The best-selling We11done on biesalab.org are: Weldon WE11DONE 2021 BLACK WOOL SILK SLIT DETAIL LONG DRESS HALTER NECK XS Used 58mm Espresso Tamper and Distributor Dual-Head for 58mm Portafilter – Adjusta… Handheld Vacuum, 13000Pa Cordless Handheld Vacuum, 120W High Power Wet and Dr… Handheld Vacuum, 13000Pa Cordless Handheld Vacuum, 120W High Power Wet and Dr… We11done Women Black Swimsuit Cover Up M WE11DONE Logo T-shirt Size L WE11DONE Logo T-shirt Size L WE11DONE Logo T-shirt Size S WE11DONE Logo T-shirt Size L We11done Cardigan Size L Brown/Beige. Perfect condition. WE11DONE Logo T-shirt Size L We11done Women Pink Pullover Hoodie S Handheld Vacuum, 13000Pa Cordless Handheld Vacuum, 120W High Power Wet and Dr… We11done Cream Sweater Print Text Washed Ivory EUC Pullover Casual Size Large WE11DONE Blue Oversized Logo Hoodie Cotton Sweatshirt Adult Size Small WE11DONE Logo T-shirt Size S WE11DONE Logo T-shirt Size L WE11DONE Logo T-shirt Size L WE11DONE Logo T-shirt Size S WE11DONE Logo T-shirt Size L WE11DONE Logo T-shirt Size S WE11DONE Logo T-shirt Size L WE11DONE Cream Yellow Boucle Pile Knit Wool Blend Oversized Sweater Unisex Small We11done Brown Coat SizeS Oversized ，Embossed logo on back We11done Jean Jacket，Dark Wash Graffiti Spell Out Logo We11done Coat. Size S. Navy Color. Perfect Condition. Authentic. We11done Lime Green Women’s Corduroy Oversized Jacket Size XS WE11DONE WASHED LOGO TEE – AUTHENTIC – NEW WITH TAGS we11done Circle Logo Embroidered Cropped Cotton Hoodie in Baby Blue One Size WE11DONE Black PF20 Collection Sweater – Size S We11done Orange Big Logo All Over Hoodie Medium oversized streetwear We11done Ivory Logo-Print Cotton T-shirt – Size S WE11 DONE Pink Cotton Sweatshirt We11done Women Pink Corduroy Jacket M WE11 DONE Maglieria WE11 DONE Maglieria We11done Women Black Long Sleeve Top S Welldone We11done Monogram Buttoned Wool Cardigan WE11 DONE Navy Blue Satin Mini Skirt XS We11Done Well Done Oversize Football 70-0411-3 WE11 DONE Logoed Baseball Cap WE11 DONE Pants M [Japan Used Fashion] Weldon We11Done 22Aw Wave Line Logo Print Hoodie Long Sleev WE11DONE/Sleeve buckle gathered belt oversize shirt/L/Polyester/BLK WE11 DONE Maglieria M WE11 DONE Maglieria M WE11 DONE Jeans WE11 DONE Black Denim Jacket S WE11 DONE Jeans WE11 DONE Jeans M WE11 DONE Jeans M WE11 DONE Short S WE11 DONE Pants M WE11 DONE Jeans Handheld Vacuum, 13000Pa Cordless Handheld Vacuum, 120W High Power Wet and Dr… Handheld Vacuum 13000Pa Cordless Handheld Vacuum 120W High Power Wet and Dry … Mens Pullover Fleece Hoodie